Máy đo độ nhớt AND SV-100 Mã đặt hàng: 11936

Máy đo độ nhớt AND SV-100 (Mã đặt hàng: 11936)

Xem tất cả 116 sản phẩm của thương hiệu AND

Ứng dụng: Máy đo độ nhớt là một thiết bị được sử dụng để đo độ nhớt của dung dịch chất lỏng. Độ nhớt là đại lượng thể hiện lực ma sát bên trong các phần tử của vật chất. Nhờ vào đại lượng độ nhớt chúng ta có thể xác định nhiều thành phần khác của vật chất.

Thông tin tồn kho:
Liên hệ
Mã sản phẩm SV-100
Thương hiệu: And
Đơn vị tính: Cái
Quy cách đóng gói: Đang cập nhật
Trọng lượng tạm tính: 1Kg
High Measurement Accuracy
Tuning-fork Vibration Method provides for excellent repeatability of 1% of reading for viscosity measurement by our Sine-wave Vibro Viscometers  SV-100.
 
 
Low Viscosity Measurement And Wide Measurement Range
Low viscosity of 0.3 mPa�s ( cP ) to high viscosity of 10,000 mPa�s ( cP ) sample fluid can be measured by the SV-10 and 1000mPa s (cP) to 100,000mPa s (cP) by the SV-100, without changing the sensor plates. 
 
 
Real-Time Measurement
The sensor plate is thin and small, in area and in mass, making it is less influenced by the temperature change of the sample fluid and as a result the viscosity measurement tracks the change of viscosity of the sample fluid.
 
SV Series
Model Range
SV-10 0.3 mPa�s (cP)
to
10,000 mPa�s (cP)
SV-100 1,000mPa s (cP)
to
100,000mPa s (cP)
Temperature Measurement
It is very important to measure the temperature of the fluid correctly because the viscosity is very much dependent upon this temperature. The SV series can detect an accurate temperature immediately because the fluid and the detection unit (sensor plates), with small surface area/thermal capacity, reach thermal equilibrium in only a few seconds. 
 
 
Continuous measurement
The SV series, Tuning-fork Vibration Method does not cause damage to the sample fluid and allows measurement of cloud point of samples such as surface active agents and of surface/interface changes such as wet ability because of its excellent feature of a wide measurement range without the need to replace the sensor plates. 
 
 
Viscosity Calibration
With Viscosity Standard, viscosity calibration can be easily done. 1 point calibration or 2 points calibration is selectable in the calibration mode. 
 
 
Non-Newtonian Sample Viscosity Measurement
Thin sensor plates allow little deformation of sample texture and thus enable measurement of stable viscosity values. 
 
 
Foaming Sample Measurement
The low drive frequency of 30Hz allows measurement of foaming samples without breaking minute foams and with less scattering of larger foams. 
 
 
Flowing Sample Measurement
Even the viscosity of flowing samples can be measured, including liquid in turbulent flow. This provides field management with identical data to that obtained in the laboratories. 
 
 
Separated type model
The SV series comprise a separate Display Unit and Main Unit offering excellent placement flexibility. 
 
 
Vacuum Fluorescent Display
Reading errors are avoided with the easy-to-read, large, clear display: 13mm height for viscosity measurement and 11mm height for temperature measurement. 
 
 
Small Sample Size
The standard sample cup requires just over 35 ml thus reducing waste. 
 
 
Easy Cleaning
Due to the simple structure, the SV series sensor plates, temperature sensor and the protector made of stainless steel (SUS 304) can all be easily and quickly cleaned. 
 
 
Sol and Gel Measurement
Sol and Gel samples can be measured during the change of material state. 
 
 
Standard RS-232C Interface
RS-232C interface and a data connection cable (DB25-DB9) are supplied as standard for your PC or printer connectivity.
 
 

Tags: Máy đo độ nhớt AND SV-100, may do do nhot and sv 100, sv 100, and

0 Khách hàng đã đánh giá về sản phẩm này
0/5
5
0%
4
0%
3
0%
2
0%
1
0%